DYSON DC04 PROBLEM SOLVING

DC02, 3, 4 and 5 are not much different. There is suction from the bottom, but only limited pick up due to the brush bar not turning. Manfromcleves on Jan 5th you are a star. Pictures will be coming soon as I understand this is hard to follow. Can I therefore please ask: What else could it be and is it worth fixing? It worked Ok for six months or so until it began to sound like a very large and powerful tractor.

Hi, I have a dc04, the brush would not turn, so, after following instructions on YouTube and discovering that the large belt was snapped I have replaced the clutch. Your remedy of removing the roller end caps and removing approximately 18 years of muck,dust and hair from the metal posts has done the trick. Now part dismantled and the belt from motor to clutch found broken. Jennifer MacArthur on March 7th, at 8: Did Dyson keep the direct drive of the roller brush. I can see from your connection you are in Colorado, if Littleton is anywhere near you, this guy will be able to do it: I have a new Dyson Animal DC59 but the roller only works intermittently.

I cleaned the filter, cleaned the brush, checked all the connections for blockage, and I even just replaced the clutch. Suction problems are mainly due to blockages or dirty filters. DC08 – Remove the cyclone and bin, open the lid at the top of the machine and wash the circular filter.

This is a serious and very very poor design fault using cheap and nasty materials not fit for purpose.

dyson dc04 problem solving

DC27 – Looking at the Dyson from the front, wash the filter at the bottom right of the machine and also the HEPA filter underneath the bin.

  HOMEWORK AND PRACTICE WORKBOOK ANSWERS ALGEBRA 1

This suction checklist below is mainly for upright Dysons as suction problems on the cylinder models are very easily solved. You will need a T15 screwdriver and this belt tool: Caren Quinn on January 17th, at 9: I can see from your connection you are in Colorado, if Littleton is anywhere near you, this guy will be able to do it: Manfromcleves on Jan 5th you are a star.

Welcome to Dyson

DC02 two rectangular filters visible once the cyclone top is opened. Hi I have the dc07 and the beater bar that stops when reclining seems as if bar is lifted and no longer touching the floor.

dyson dc04 problem solving

Dyson Spares – The Dyson Forums. I removed this and even popped the plastic off the end of the bearings. Cord-free vacuums Full size pfoblem Heating and cooling. Cheryl Sweeney on March 8th, at DC02, 3, 4 and 5 are not much different.

If you are testing it in the upright position then suction is diverted to the wand.

I replaced a clutch a while back and fc04 seemed ok. Had a look at the DC24 recently and realised that the brush roller at the drive end and clutch were causing the roller to wobble about like a bandy knee. DC27 – Looking at the Dyson from the front, wash the filter at the bottom right of the machine and also the HEPA filter underneath the bin.

Dyson vacuum cleaner wand handle suction problems troubleshooting

Convenient, portable vacuum cleaners Quickly switch between stick and handheld mode Clean from floor to ceiling. Hi I am trying to help an elderly gentleman by fixing solvng Dyson dc Suzanne on September 19th, at 1: So I removed the brush bar, pulled both ends off to find they were both full of hair and dirt. Check the hose all the way along for splits and tears usually they start under the top cuff but check the entire hose just in case If the hose has a small tear in it and it is not fully stretched out then you are not going to lose massive amounts of suction, it will need replacing but don’t buy a hose until you figure out what else is causing the loss in suction.

  CASE STUDY CTTS - MILESTONE 09

Help from Dyson experts.

Or possibly a micro switch. My money is on the loom, it is this one: I replaced the clutch and still no luck.

dyson dc04 problem solving

Angus Black on December 2nd, at 8: Having suction problems with your Dyson? I can see from your connection you are in Oslving, if Littleton is anywhere near you, this guy will be able to do it: I reclined it with it on carpet and still nothing. If after cleaning your filters and checking every orifice of your machine your suction is still poor, click here to troubleshoot your Dyson DC07 vacuum.

Occasionally it will if you hold the handle at a certain angle. Leave this anti-spam sollving empty.